JIAWEI WIGS CO.,LTD- Human Hair| Wigs| hair| Remy Hair
HUMAN HAIR[75]
HH Straight(9)
HH Yaki(9)
HH Curly(33)
Clips on hair extension(10)
Human hair wigs(8)
Skin Weft(3)
hand tied weft(3)
SYNTHETIC HAIR[351]
Long Wig(75)
Medium Wig(53)
Short Wigs(58)
Halloween Wig(55)
Hair Extension(32)
Instant Weave(11)
Monotop Wigs(6)
Mannequin Head(14)
Cosplay Wig(47)
KERATIN HAIR[33]
Nail Hair(5)
Stick Hair(10)
Tri-angle Hair(9)
Flat Hair(9)
TOUPEE[33]
Toupee(16)
Base(17)
HAIR ACCESSORIES[119]
Beard or Eyebrowm(6)
Hair Nets(2)
Positch(54)
Hair Piece(27)
Other(30)
REMY HAIR[6]
Remy Straight(3)
Remy Curley(3)
LACE WIGS[39]
Full Lace Wigs(13)
Lace Front Wigs(7)
Synthetic lace front(19)
BRASILIAN HAIR[6]
Brasilian Weft(6)
Brasilian Bulk(0)
  
 
 
 
  
  Name:
 
  Password：
 
   
 
  Jiawei Printing Co., Ltd
 
    Skype Me?!
    lina2004
 

MIRCO LINK SYSTEM
   
1. Section client'hair.
  
2. Insert pulling needle through tube.
  
3. Graba portion of client's hair with pulling needle.
 
   
4. Slide the portion of hair through tube.
  
5. Hold the tube 5 to 1 inch from scalp.
  
6. Insert stick through the tube.
 
     
7. Flatten the tube.
  
8. Finished and repeat steps. Hair can be reused. Remove the pre-tipped piece with remover, cut off the glue tip and use your glue gun with adhensive sticks to reapply.
    
 
 
REMOVAL PROCESS
   
1. Position tube in first groove of tube opener and qpply pressure slowly.
  
2. Slide out the extension hair after opening the tube.
  
 

GLUE EXTENSIONS SYSTEM
   
1.Start sectioning client's hair from bottom to top.


  
2.Insert protection pad to root to protect scalp from heat.
  
3.Twist strands to ease placing nail hair.
 
   
4.Place nail hair under client's hair, holding with on hand.
  
5. Place hair connector under hair.
  
6. Pinch smoothly for about 3 seconds to melt and smear glue into every hair stand.
 
   
7. Roll fused part with fingers and try to close tightly.
  
8. Finished - Do not shampoo or condition hair within 24 hours.
  
Fusion Connector Iron
 
   
Protection Pad
  
Nail Hair
  
Fingers
REMOVAL PROCESS
1. Apply 3-4 drops of safe Remover on glued part and then use flat pliers to break it.
2. Separate nail hail from client's hair and then use comb or shampoo to remove glue residue.

SKIN WEFT

   
1.Before
  
2.Section client's hair
  
3.Measure the desired width
 
   
4.Remove the backing and apply the skin tape onto the base
  
5.Attach the base directly on the hair about inch below the scalp
  
6.Raise the top layer along with some of your own
 
   
7.Only a small thin layer of your own hair is needed in between the skin extesnions
  
8.Remove the backing on the second layer
   9.Attach the layer underneath the first layer.Be sure to attach it evenly against the top layer
     
   
10.After both layers are attached,your own hair is between the two hair extensions
  
11.To increase the adhesion of the glue,heat the skin base with a low heat heating iron.Seal for about 10 secs.
   12.After completing the section
     
   
After
  
Skin glue
   Skin weft extensions adhibit glue
       
Skin weft extensions
        
 

COPYRIGHT (C)2004-2009 JIAWEI WIGS CO., LTD. 备案信息：粤ICP备06044586号